Name: Orange Lizard Leather Watch Strap
Brand: Mocgoods
SKU: MG-1612
Price: 89.0 USD
Availability: InStock

FROM OUR WORKSHOP

How Your Strap Is Made

Every strap takes a full day of careful work in our Da Nang workshop. Here is how yours is made.

Step 01

Reading the hide

Not every part of a hide makes a strap. The belly scales need to fall straight - centered, regular, no skipped rows. We walk the template across the panel until the rows line up under it, then mark where the cut will go.

Alligator panel with the strap template laid across the belly scales

Hand placing the template over an even row of scales

Drawing the strap pattern on kraft paper with a ruler

Marking the buckle end of the pattern with an awl

Step 02

Drawing the pattern

The pattern goes on kraft paper at full size. Tail length, buckle end, taper, pin holes - all set on paper before a blade touches the leather. Mistakes here are cheap; mistakes after this point are not.

Step 03

Cutting

The kraft template is traced onto the back of the hide with a fine awl, then cut by hand with a fresh blade. One steady pull per line. If the line wavers, the piece goes to the scrap pile - we never try to save a bad cut.

Trimming the strap to the pattern line by hand

The six pieces that go into one finished strap, laid out before assembly

Step 04

Stacking the layers

Six pieces make one strap: top exotic, a calfskin underlayer, closed-cell foam for the curve, the lining for the wrist side, plus two thin strips for the keeper loops. Everything is dry-fit first, before any glue touches anything.

Step 05

Skiving

Each edge runs through the bell skiver - a small rotating disc that shaves the leather down to a fine ramp. Hold the piece wrong and you cut through. We have been over this machine thousands of times; the hand finds the angle on its own now.

Feeding the leather through the bell skiver to thin the edge

Bell skiver shaving the edge down to a fine ramp

Brushing latex contact glue onto the lining

Pressing the glued layers together by hand

Step 06

Glue and assemble

Latex contact glue, brushed on both sides, left to tack. The layers go together once - the bond is permanent, so the alignment has to be right the first time. The strap takes shape between two thumbs.

Step 07

Trimming the blank

The glued blank is trimmed back to the pattern line and the edges flattened with a fresh blade. This is the first moment the strap looks like a strap - one clean shape, ready for the stitch line to be marked.

Assembled strap pair after final trim, ready for the stitch line

Brass pricking iron struck along the edge to mark stitch holes

Working the pricking iron forward, hole by hole

Step 08

Marking the stitch line

A brass pricking iron is struck with a poly mallet down the edge, walked forward one tooth, struck again. Every hole is set in advance - so the needle never has to guess where it is going next.

Step 09

Saddle stitching

Strap clamped in a wooden pony. Two needles loaded with waxed polyester thread, both hands moving in opposite directions, locking each stitch in place. Hours per side. The result is a stitch that cannot run - cut one and the next ones hold.

Two needles working both sides of the strap at once

Strap clamped in the pony, waxed thread mid-stitch

Applying matched edge paint along the stitched edge

Close-up of the edge paint laid down in a clean line

Step 10

Edge painting

Edge paint is mixed to match the strap colour, in small batches. A fine applicator lays it down in a thin pass. The edge is heat-set, sanded back with very fine grit, and the next pass goes on. Three to five passes - until the seam reads as one piece of edge.

Step 11

Boxed and shipped

Last check: stitch count, edge finish, leather grain, buckle alignment. Anything off goes back. The strap is laid into a Moc Goods box with a handwritten thank-you card, sealed, and shipped from Da Nang to your door with tracking.

Hand placing the thank-you card on the open gift box

Moc Goods gift box with the finished strap ready to ship

Eleven steps, one pair of hands, one full day on the bench.
— Moc Goods Workshop, Da Nang

BUILT FOR DAILY WEAR

Watch Strap Structure

Each Moc Goods watch strap is built around three details that matter most for daily wear. Pre-installed Quick Release spring bars let you swap straps in seconds without tools or scratches on the lugs.

The underside is lined with soft, water-resistant Zermatt - the same lining used by leading watch strap makers worldwide - for all-day comfort, even in warm weather. And every strap can be hand-stamped with your name or initials, free of charge, so the piece on your wrist is one of one.

Watch strap structure with quick release spring bar, soft lining and personalized engraving

Moc Goods premium watch strap gift box with thank-you card

GIFT-READY

Strap Packaging That Protects

Every strap ships in a Moc Goods gift box, hand-packed in our Da Nang workshop. A handwritten thank-you card is tucked inside, and each strap is wrapped in a soft cotton sleeve so the leather arrives unmarked.

Orders of four or more straps ship in our larger presentation box. Ready to give as-is - no extra wrapping needed.

Material	Premium lizard leather
Stitching	Tone-on-tone, full-edge hand-stitching
Lug - Buckle (mm)	18-14, 19-16, 20-16, 21-18, 22-18
Length (mm)	Short 105/65, Regular 115/75, Long 125/85
Lining	Zermatt Golden

Orange Lizard Leather Watch Strap

About Lizard Leather